LAND MOBILE RADIO PRODUCTS ONLY
MAYBE YOU WOULD LIKE TO BECOME A "WADSWORTH SALES" DEALER? MANY OF OUR DEALERS WORK FULL TIME JOBS AND DO THE RADIO BUSINESS AS A "SIDE BUSINESS". WE HAVE MANY ESDA/RACES/ARES ORGANIZATIONS, GMRS AND COMMERCIAL 2-WAY DEALERS AS WELL.
IF YOU THINK YOU MIGHT LIKE TO INVESTIGATE THIS VENTURE JUST E-MAIL OR GIVE US A CALL!
BEING A MANUFACTURER'S REPRESENTATIVE WE PROCESS NO ORDERS DIRECTLY
BUT INSTEAD SET UP DEALERS AND DIRECT END USERS TO OUR DEALERS.
CELL PHONE (815) 790-4494 ~ SKYPE PHONE = bryan.wadsworth ~ FAX (815) 363-6056
| | C-150BX-H | 148-175MHz (tunable) fixed station antenna
1.5:1 or less SWR: 4MHz after tuning
Gain: 3.4dBi
Max power: 100 watts
Length: 50.5 inches max
Weight: 2 lb 2oz
Connector: SO-239
Construction: Telescoping Aluminum pipe
Max wind speed: 112MPH |
| | | |
|
| | C-150BX-L | 118-145MHz (tunable) fixed station antenna
1.5:1 or less SWR: 4MHz after tuning
Gain: 3.4dBi
Max power: 100 watts
Length: 67 inches max
Weight: 2 lb 6oz
Connector: SO-239
Construction: Telescoping Aluminum pipe
Max wind speed: 112MPH |
| | | |
|
| | CA-F22GF | 136-175MHz (tunable) fixed station antenna
1.5:1 or less SWR: 4MHz after tuning
Gain: 5.5dBi
Max power: 150 watts
Length: 8 ft 10 inches
Weight: 2lbs 8 ozs
Connector: SO-239 (CA-F22GFN N-female connector)
Construction: Two-piece black fiberglass
Max wind speed: 112MPH |
| | | |
|
| | CA-SUPER22 | 220MHz fixed station antenna
1.5:1 or less SWR: 220-225Mhz
Gain: 6.6dBi
Max power: 150 watts
Length: 8 ft
Weight: 2 lb 2oz
Connector: SO-239
Construction: One piece black fiberglass
Max wind speed: 112MPH |
|
|
| | CA-712EFC | UHF Fixed station antenna
1.5:1 or less SWR: 460-470MHz
Gain: 9dBi
Max power: 200 watts
Length: 10 ft 5 inches
Weight: 2 lb 13oz
Connector: N-female
Construction: Two piece white fiberglass
Max wind speed: 112MPH |
| | | |
|
| | CA-F72GF | 440-512MHz (tunable) fixed station antenna
1.5:1 or less SWR: 10MHz after tuning
Gain: 5.5dBi
Max power: 150 watts
Length: 42 inches
Weight: 2 lb 14oz
Connector: N-female
Construction: One-piece white fiberglass
Max wind speed: 135MPH |
|
|
| | GP-6NC | VHF/UHF Dual Band Antenna
1.5:1 or less SWR: 153-157/460-470MHz
Gain: 6.5/9.0dBi
Max power: 200 watts
Length: 10 ft 2 inches
Weight: 3 lb 8 oz
Connector: N-female
Construction: Two piece white fiberglass
Max wind speed: 112MPH |
| | | |
|
| | GP-9NC | VHF/UHF Dual Band Antenna
1.5:1 or less SWR: 153-157/460-470MHz
Gain: 8.5/11.9dBi
Max power: 200 watts
Length: 16ft 6inches
Weight: 3 lb 8 oz
Connector: N-female
Construction: Three piece white fiberglass
Max wind speed: 92MPH |
| | | |
|
| | GP-9NCA | VHF/UHF Dual Band Antenna
1.5:1 or less SWR: 150-154/460-470MHz
Gain: 8.5/11.9dBi
Max power: 200 watts
Length: 16ft 6inches
Weight: 3 lb 8 oz
Connector: N-female
Construction: Three piece white fiberglass
Max wind speed: 92MPH |
|
|
| | CFC-771 | 900MHz Access Point Antenna
1.5:1 or less SWR: 900-930MHz
Gain: 7.14dBi
Max power: 50 watts
Length: 51 inches
Weight: 1lb 8oz
Connector: N-female
Construction: One-piece white fiberglass
Max wind speed: 135MPH |
| | | |
|
| | KP-20 | 900MHz Access Point Antenna
1.5:1 or less SWR: 900-930MHz
Gain: 9.2dBi
Max power: 50 watts
Length: 8 ft
Weight: 2 lb 4oz
Connector: N-female
Construction: One-piece white fiberglass
Max wind speed: 100MPH |
|
|
| | CLP-5130-1N | Wideband log periodic receive/transmit antenna
2:1 or less SWR: 50-1300MHz
Elements: 21
Polarization: Horizontal
Gain: 10-12dBi
F/B ratio: 15dB
Half power point:
70-60 degree
Max power:
500 watts
Boom length:
6ft 8 inches
Max element length:
9 ft 10 inches
Weight: 11 lbs
Connector:
N-connector
Construction:
Aluminum
Max wind speed:
90MPH |
| | | |
|
| | CLP-5130-2N | Wideband log periodic receive/transmit antenna
2:1 or less SWR:
105-1300MHz
Elements: 17
Polarization:
Horizontal
Gain: 11-13dBi
F/B ratio: 15dB
Half power point:
70-60 degree
Max power:
500 watts
Boom length:
6ft 8 inches
Max element length:
4 ft 4 inches
Weight: 11 lbs
Connector:
N-connector
Construction:
Aluminum
Max wind speed:
90MPH |
|
|
| | CA-2x4SR | BROADBAND VHF/UHF Dual Band Antenna CA-2x4SR: Designed to assist Search & Rescue Volunteers and Professionals
1.5:1 or less SWR: 140-160/435-465MHz
Gain: 3.8/6.2dBi
Max Power: 150 watts
Length: 40 inches
Connector: PL-259
Fold-over hinge included The CA-2x4SR is a broad-band antenna designed for those needing voice communications on both the ham radio and land mobile frequency ranges. When the amateur radio community is working together with local search and rescue and other public service agencies, the CA-2x4SR antenna allows TX and RX capability in both bands! The coverage area and gain provided by the CA-2x4SR is remarkable. Whether used on VHF or UHF or both, it is an asset to the communications needs of amateurs and land mobile users simultaneously. |
| | | | CLICK ON >>> CA-2x4SR ANTENNA REVIEWS PDF <<< CLICK ON |
|
| | FC-54NMO | VHF/UHF Dual Band Antenna
1.5:1 or less
SWR:
153-157/460-470MHz
Gain: 2.15/5.0dBi
Max Power: 50 watts
Length: 36 inches
Connector: NMO
Fold-over hinge included |
|
|
| | R-2000 | 900 MHz Mobile antenna
1.5:1 or less SWR: 900-930MHz
Gain: 5.1dBi
Max Power: 30 watts
Length: 19.25 inches
Connector: N-male |
|
|
| | CM-5M | Standard 4.5” magnet mount with SO-239/PL-259 connectors with 13’ of RG-58A/U coax. |
| | | |
|
| | CP-5M | Universal adjustable lip mount, 16’ 6” deluxe cable assembly with SO-239/PL-259 connectors. Quality appearance and low loss coax cable assembly. Installs easily in only minutes to virtually any lip on a vehicle. Trunk lid, truck rear doors, SUV and van rear doors, hood lip, etc… Does not damage expensive and/or leased vehicles.
Footprint: 3.4" x 1.25"
Mount adjusts in 4 planes. The first 18 inches of coax is mini RG-188A/U type allowing easy entry through the weather seal into the vehicle without causing wind noise, water leaks or coax damage. The coax balance is low loss with 24k gold plated SO-239 & PL-259 connectors. The PL-259 disassembles for easier routing or to shorten the coax length. Soft rubber pad protects the vehicle paint, 4 large set screws hold the mount firmly in place.
|
| | | |
|
| | CP-5NMO | Universal adjustable lip mount, 16’ 6” deluxe cable assembly with NMO/PL-259 connectors. Quality appearance and low loss coax cable assembly. Installs easily in only minutes to virtually any lip on a vehicle: Trunk lids, truck rear doors, SUV and van rear doors, hood lip, etc… Does not damage expensive and/or leased vehicles.
Footprint: 3.4" x 1.25"
Mount adjusts in 4 planes. The first 18 inches of coax is mini RG-188A/U type allowing easy entry through the weather seal into the vehicle without causing wind noise, water leaks or coax damage. The coax balance is low loss with NMO & PL-259 connectors. The PL-259 connector disassembles for easier routing or to shorten the coax length. Soft rubber pad protects the vehicle paint, 4 large set screws hold the mount firmly in place.
|
| | | |
|
| | CT-5M | Standard trunk lip mount with SO-239/PL-259 connectors. Adjusts up to 17 degrees to compensate for trunk angle. Included
16’ 6” of RG-58A/U. |
| | | |
|
| | GR-5N | Designed for use with 900-2500MHz mobile antennas that use N-male connectors.
Deluxe trunk lip mount, 16’ 6” cable length with N-female/N-male connectors. Adjusts up to 17 degrees to compensate for trunk angle. Quality appearance and low loss coax cable assembly installs easily in minutes.
The first 18 inches of coax is mini RG-188A/U type allowing easy entry through the weather seal into the vehicle without causing wind noise, water leaks or coax damage. The coax balance is low loss with 24k gold plated N connectors. The N-male connector disassembles for easier routing or to shorten the coax length. Soft rubber pad protects the vehicle paint, 4 large set screws hold the mount firmly in place. |
| | | |
|
| | GRB-5M | Deluxe trunk lip mount, 16’ 6” cable length with SO-239/PL-259 connectors. Adjusts up to 17 degrees to compensate for trunk angle. Quality appearance and low loss coax cable assembly installs easily in minutes. Footprint: 4.25" x 1.9"
The first 18 inches of coax is mini RG-188A/U type allowing easy entry through the weather seal into the vehicle without causing wind noise, water leaks or coax damage. The coax balance is low loss with 24k gold plated SO-239 & PL-259 connectors. The PL-259 connector disassembles for easier routing or to shorten the coax length. Soft rubber pad protects the vehicle paint, 4 large set screws hold the mount firmly in place. |
|
|
| | EM-B80 | Light-Duty, 2 adjustment planes, up to 40” antenna 1.1" x .75 inch footprint allows the EM-B80 to be mounted in a very limited space. Fits where other mounts won't! |
| | | |
|
| | MK-30H | 12VDC motorized mount for trunks/hatch-backs, rear van doors etc. Heavy Duty motor provides convenient lowering/raising of a mobile antenna. Approximately 17 feet of wire allows the up/down switch to be located within the drivers reach. Recommended for antennas up to 70” and weighing 1lb. 3oz. or less. Rubber coated base avoids scratches. Coax cable not included. |
| | | |
|
| | RS-840 | Heavy-duty, up to 80” antenna REPLACEMENT FOR THE PRM-T THAT IS NOW OBSOLETE |
| | | |
|
| | RS-520 | Light duty, 3 adjustment planes, up to 45” antenna |
| | | |
|
| | RS-560C | Heavy-duty roof rack/pipe clamp mount. Max opening: 1 7/8”x1 7/8” |
| | | |
|
| | RS-720/RS-720NMO | Med-duty, 3 adjustment planes, up to 60” antenna. The RS-720NMO has a 3/4” hole to accept an NMO mount. |
| | | |
|
| | RS-730 | Heavy-duty 3 adjustment planes, up to 70” antenna |
|
|
| | 3D4M | Standard Cable Assembly.
13 feet of low loss coax. Gold-plated UHF
(PL-259/SO-239) connectors. |
| | | |
|
| | 3D4N | Standard Cable Assembly with N-Connectors.
Recommended to 900MHz. 13 feet low loss coax |
| | | |
|
| | 3D5M | Standard Cable Assembly.
16 feet 9 inches 13 feet of low loss coax. Gold-plated UHF
(PL-259/SO-239) connectors |
| | | |
|
| | 5D4N | 13 feet of extremely low loss coax. Gold-plated N-type connectors. Recommended up to 2400MHz. |
| | | |
|
| | CK-3M | Deluxe Cable Assembly. 10 ft. total length including 18 inches of RG-188 teflon coax for easy entry from a lip-mount, without causing wind noise, coax damage or water leaks. Gold-Plated UHF (SO-239/PL-259) connectors. |
| | | |
|
| | CK-3M5 | Deluxe Cable Assembly.
16 feet 9 inches total length including 18 inches of RG-188 teflon coax for easy entry from a lip-mount, without causing wind noise, coax damage or water leaks. Gold-Plated UHF (SO-239/PL-259) connectors. |
| | | |
|
| | CR-5M | Standard Cable Assembly
16 feet 9 inches of RG-58/U coax with UHF
(PL-259/SO-239) connectors |
|
|
MAYBE YOU WOULD LIKE TO BECOME A "WADSWORTH SALES" DEALER? MANY OF OUR DEALERS WORK FULL TIME JOBS AND DO THE RADIO BUSINESS AS A "SIDE BUSINESS". WE HAVE MANY
ESDA/RACES/ARES ORGANIZATIONS, GMRS AND COMMERCIAL 2-WAY DEALERS AS WELL.
IF YOU THINK YOU MIGHT LIKE TO INVESTIGATE THIS VENTURE JUST E-MAIL OR GIVE US A CALL!
BEING A MANUFACTURER'S REPRESENTATIVE WE PROCESS NO ORDERS DIRECTLY
BUT INSTEAD SET UP DEALERS AND DIRECT END USERS TO OUR DEALERS.
CELL PHONE (815) 790-4494 ~ SKYPE PHONE = bryan.wadsworth ~ FAX (815) 363-6056
Q. What is your best dualband mobile antenna?
A. The answer depends entirely on what you are looking for. Highest gain for maximum coverage area? The new CSB-790A (150W) or the SBB-7 or SBB-7NMO (70W)
Lowest profile for entering garages? B-10 or B-10NMO
Most durable for operating on a motorcycle, 4WD truck or Semi truck? The HP-32FHN.
The best antenna is the best for your situation and typical operating area.
Q. Whats the difference between NMO and the PL-259 type mounts?
A. If you decide to drill a hole in your car, the NMO (New MOtorola) mount was designed specifically for hole installations. They can be installed from the top and are water proof. So if you want to drill a hole, you should use an antenna with an NMO connector. If you DO NOT want to drill a hole in your vehicle, there are many more external mounts available to choose from made for PL-259 connector antennas.
Q. Should I drill a hole in my roof/trunk or use a lip mount?
A.In the past, most people preferred drilling a hole in the center of the roof or trunk to provide the best ground plane. This made a lot of sense when the repeater systems were poor and most antennas were single band and needed the ground plane. Current antenna design produces antennas that are ground independent. The sensitivity, coverage area and height of most modern repeater systems is outstanding. The antenna no longer needs to be in the middle of a ground plane for excellent coverage.
The benefit of drilling a hole and mounting your antenna in the middle of the roof or trunk is minimal.
Hole Mounting: Difficult to reach the antenna to remove it or use the fold-over hinge
Water leaks and rust problems are common.
Lip Mount Benefits:
Lip mount installation is quick, easy and no damage to the car
The antenna is easily reached for removal or to use the fold-over hinge
Deluxe coax cable easily enters through the weather seal without causing any wind noise, water leaks or coax damage.
Mount can be removed and re-used on a different vehicle
Slightly distorted radiation pattern
Because most people look to Comet and Maldol for no holes to drill mounting options, their antennas are tuned for best performance on a lip mount.
Q. I have a truck, where can I mount an antenna?
A. If your truck has a third door or rear doors, the best location for a lip mount is the side of the drivers side rear door near the top. The antenna is above the roof line, no holes to drill and mounting takes only a few minutes.
Q. What mount should I use for a plastic/composite car?
A. Most of the Comet and Maldol antennas we distribute are ground independent and can be mounted to new plastic/composite cars with the standard lip mounts. The exception is any antenna that has an electrical length of 1/4 wave. A 1/4 wave antenna is only half an antenna, the other half is the ground plane. So, a 1/4 wave has to be grounded to work well and have good SWR.
Q. I have a SUV/VAN that doesnt have a trunk, where can I mount an antenna?
A. We receive many calls from people worried that they can't mount an antenna because they dont have a trunk. If you have an SUV or van with a back door, you have the best possible mounting location and you dont even know it. The rear door, whether hatchback style or cargo doors, is the best place for a lip mount. Simply lift or open the drivers side door, slip the preferred mount over the edge near the top of the door and tighten the set screws that hold it to the door. Rotate all the pieces until the mount is vertical, add a coax cable if not included and its mounted. The antenna is above the roof line for the best pattern, its easy to reach if you need to take it off for a car wash or fold it over to get in a garage, no holes are needed and mounting takes only a few minutes.
Q. What mount should I use?
A. Choose the mount that is most appropriate for the antenna you want to use. They all attach the same way. Set screws hold them to the edge, a piece of soft rubber protects the painted surface. The only decision is the size of the antenna should match the mount size. Keep in mind that you may want to get a bigger VHF/UHF or heavier HF antenna some time in the future, so choose the mount size keeping that in mind. We don't have the ability to test all our mounts on every vehicle made, so we can't answer questions related to specific vehicles and model years. However, all of our mounts will attach to virtually any lip on any vehicle provided the thickness of the lip is 1/4 inch or less. Some newer vehicles are using composite materials for some parts. The composite has to be thicker than steel to have the same strength, so it is sometimes more than 1/4" thick. Check the thickness where you want to mount it.
Q. Can I buy parts if I break my antenna?
A. We keep many parts on hand for most but not all antennas. If an antenna has been discontinued, no parts will be available.
Q. Did Comet buy Daiwa and Maldol?
A. No, all three are separate companies in Japan. NCG is the US distributor for all three.
Q. Whats the difference between Comet and Diamond, are they the same company?
A. Comet and Diamond make similar products just as Ford and GM do. Sometimes the same sub-contractors will make parts for both, so the parts will look similar. They both pay attention to quality, innovation and focus on making the best product they can. We feel Comets engineers and quality control are second to none and are proud of their US distributor.
 |
|
| | HT-55 | VHF/UHF Handheld Antenna
2:1 or less SWR: 153-157/460-470MHz
Wide range receive: 118-960MHz
Max Power: 5 watts
Length: 8.75 inches
Connector: SMA-male |
| | | |
|
| | MH-255 | VHF/UHF Handheld Antenna
2:1 or less SWR: 153-157/460-470MHz
Wide range receive: 118-960MHz
Max Power: 5 watts
Length: 3 inches
Connector: SMA-male |
|
|
| | CF-142 | 146/220MHz
Band Pass Ins. Loss Max Power
1.3-150MHz 0.2dB 600w PEP
200-480MHz 0.3dB 400w PEP
Isolation: 40dB
CONNECTORS:
Output: Low In: High In:
SO-239 PL-259 PL-259 |
| | | |
|
| | CF-360A | HF/6M-440MHz Duplexer
Band Pass
1.3-30MHz
49-470MHz
Ins. Loss
0.2dB
0.2dB
Max Power
600w PEP
600w PEP
Isolation:
More than 45dB
CONNECTORS:
Output:
SO-239
Low In:
PL-259
High In:
PL-259 |
| | | |
|
| | CF-360B | HF/6M-440MHz Duplexer
Band Pass
1.3-30MHz
49-470MHz
Ins. Loss
0.2dB
0.2dB
Max Power
600w PEP
600w PEP
Isolation:
More than 45dB
CONNECTORS:
Common:
PL-259
Low In:
SO-239
High In:
SO-239 |
| | | |
|
| | CF-4160K, 4160I, 4160J | 146/446MHz
Band Pass Ins. Loss
1.3-170MHz 0.1dB 800w PEP
350-540MHz 0.2dB 500w PEP
Isolation: 60dB
CONNECTORS:
CF-4160K CF-4160I CF-4160J
Output: SO-239 SO-239 SO-239
Low In: PL-259 PL-259 SO-239
High In: PL-259 N-Male SO-239 |
| | | |
|
| | CF-416A, 416B, 416C | Band Pass Ins. Loss Max Power
1.3-170MHz 0.15dB 800w PEP
350-540MHz 0.25dB 500w PEP
Isolation: 60dB
CONNECTORS:
CF-416A CF-416B CF-416C
Output: SO-239 SO-239 N-Female
Low In: PL-259 PL-259 PL-259
High In: PL-259 N-Male N-Male |
| | | |
|
| | CF-416W | Multi-Option Duplexer
2M/440MHz –
220MHz/440MHz –
2M/440-1200MHz
Band Pass
1.3-250MHz
400-1400MHz
Ins. Loss
.2dB
.25-.3dB
Max Power
400w PEP
200w PEP
Isolation: 30dB
CONNECTORS:
Output:
N-Female
Low In:
PL-259
High In:
N-Male |
| | | |
|
| | CF-530 | HF/6M/2M-70cm Duplexer
For the IC-706/MKII/G FT-100
Band Pass
1.3-90MHz
125-470MHz
Ins. Loss
0.2dB
0.2dB
Max Power
600w PEP
600w PEP
Isolation:
More than 45dB
CONNECTORS:
Output:
SO-239
Low In:
PL-259
High In:
PL-259 |
| | | |
|
| | CF-530C | HF/6M/2M – 70cm Duplexer
for the FT-8900
Band Pass
1.3-90MHz
125-470MHz
Ins. Loss
0.2dB
0.2dB
Max Power
600w PEP
600w PEP
Isolation:
More than 45dB
CONNECTORS:
Output:
PL-259
Low In:
SO-239
High In:
SO-239 |
| | | |
|
| | CF-706A | HF-6M/75MHz-70cm Duplexer for the IC-706/MKII/G, FT-100
Band Pass Ins. Loss Max Power
1.3-57MHz 0.4dB 350w PEP
75-550MHz 0.4dB 350w PEP
Isolation: More than 40dB
CONNECTORS:
Common: Low pass: High pass:
SO-239 PL-259 PL-259 |
|
|
| | CFX-324A | 146/220/446MHz Triplexer
Band Pass
1.3-150MHz
200-320MHz
390-500MHz
Ins. Loss
0.2dB
0.25dB
0.3dB
Max Power
600w PEP
600w PEP
600w PEP
Isolation: 40dB
CONNECTORS:
CFX-324A
Output: SO-239
Low In: PL-259 w/coax lead
Mid In: PL-259 w/coax lead
High In: PL-259 w/coax lead
CFX-324B
Output: SO-239
Low In: PL-259
Mid In: PL-259
High In: PL-259 |
| | | |
|
| | CFX-324B | 146/220/446MHz Triplexer
Band Pass Ins. Loss Max Power
1.3-150MHz 0.2dB 600w PEP
200-320MHz 0.25dB 600w PEP
390-500MHz 0.3dB 600w PEP
Isolation: 40dB
CONNECTORS:
CFX-324A CFX-324B
Output: SO-239 SO-239
Low In: PL-259 PL-259
Mid In: PL-259 PL-259
High In: PL-259 PL-259 |
| | | |
|
| | CFX-4310C | 146/446/1200MHz
Band Pass Ins. Loss Max Power
1.3-60MHz 0.15dB 1000w PEP
100-150MHz 0.25dB 800w PEP
350-500MHz 0.25dB 500w PEP
840-1.4GHz 0.3dB 200w PEP
Isolation: 50dB
CONNECTORS: CFX-4310C
Output: N-Female
Low In: PL-259
Mid In: PL-259
High In: N-Male |
| | | |
|
| | CFX-514 | 50/146/446MHz
Band Pass Ins. Loss Max Power
1.3-90MHz 0.2dB 800w PEP
130-200MHz 0.25dB 800w PEP
380-500MHz 0.3dB 500w PEP
Isolation: 55dB CONNECTORS:
Output: Low In: Mid In: High In:
SO-239 PL-259 PL-259 PL-259 CFX-514N: Has an N-Conn on 70cm. CFX-5140: Same as CFX-514, but without coax leads. |
| | | |
|
| | CFX-514J | 50/146/446MHz
Band Pass Ins. Loss Max Power
1.3-90MHz 0.15dB 800w PEP
130-200MHz 0.2dB 800w PEP
380-500MHz 0.25dB 500w PEP
Isolation: 55dB
CONNECTORS:
Output: Low In: Mid In: High In:
SO-239 SO-239 SO-239 SO-239 |
|
|
| | CN-101 | Frequency: 1.8-150MHz
Power Range Forward: 15/150/1.5kW
Power Rating:
1.5kW (1.8-60MHz)
1kW (144MHz)
Tolerance: +/- 10% (at full scale)
SWR Detection Sensitivity: 4 W min
Input/Output Impedence: 50 OHM
Input/Output Connectors: SO-239
Dimensions & Weight: 5” x 3” x 4” / 1lb. 8ozs. |
| | | |
|
| | CN-103M/CN-103N | Frequency: 140-525MHz
Power Range Forward: 20/200kW
Power Rating:
200W
(140-525MHz)
Tolerance: +/- 10% (at full scale)
SWR Detection Sensitivity: 4 W min
Input/Output Impedence: 50 OHM
Input/Output Connectors: SO-239/N-Type
Dimensions & Weight: 5” x 3” x 4” / 1lb. 8ozs. |
| | | |
|
| | CN-801H | Frequency: 1.8-200MHz
Power Range Forward: 20/200/2kW
Tolerance: +/- 10% (at full scale)
SWR Detection Sensitivity: 5 W min
Input/Output Impedence: 50 OHM
Input/Output Connectors: SO-239
Dimensions & Weight: 6.25” x 4.3” x 4.8” / 2lbs. 3ozs. |
| | | |
|
| | CN-801SII | Frequency: 900-2500MHz
Power Range Forward: 200mW/2/20W
Tolerance: +/- 10% (at full scale)
SWR Detection Sensitivity: 0.5 W min
Input/Output Impedence: 50 OHM
Input/Output Connectors: N-Type
Dimensions & Weight: 6.25” x 4.3” x 4.8” / 2lbs. 3ozs. |
| | | |
|
| | CN-801V | Frequency: 140-525MHz
Power Range Forward: 20/200W
Tolerance: +/- 10% (at full scale)
SWR Detection Sensitivity: 5 W min
Input/Output Impedence: 50 OHM
Input/Output Connectors: SO-239
Dimensions & Weight: 6.25” x 4.3” x 4.8” / 2lbs. 3ozs. |
|
|
| | CMX-1 | Remote sensor, cross needle SWR/Power meter
Full color lighted meter display head
6’ remote cable included (EKS-3 options adds 10’/16’ total)
Frequency range: 1.8-60MHz
Power ranges: 30W/300W/2kW
Input loss: Less than 0.2dB
Connectors: SO-239
Minimum power for SWR measurement: 6 watts (1pprox)
Monitor forward power, reflected power and SWR
simultaneously |
| | | |
|
| | EKS-3 | Optional 10’ extension cable for CMX-1 remote sensor SWR meter |
|
|
| | SS-330W | 30 Amp switching power supply
30 amps continuous
Simple change from 110V to 230V input
Adjustable output voltage: 5-15V
Dual meters
Built-in quite fan
Light weight: 4lbs 4ozs
Dimensions: 5” x 4” x 11”
Carry handle |
| | | |
|
| | SS-505 | 50 Amp Switching Power Supply
50 amps continuous (55A max)
50 amps available at ALL DC output voltages
Adjustable voltage: 5-15V
Dual purpose Amp/Voltage meter
Protection: Cut-off at 56 Amps
Automatic cooling fan
Voltage fluctuation: Less than 1.5%
Ripple voltage: Less than 5mV
Conversion ratio: 84% at 35 Amps
Power consumption: 920W
Dimensions: 9"w x 5"h x 12.5"d (approx)
Weight: 8lbs 4ozs
Binding posts on back panel, lighter socket and spring connectors on front panel. Carry handle and rubber cushions around the front and rear panels for portability |
|
|
 |
|
| | Power Pocket | 12V/2AH rechargeable sealed lead-acid battery pack
The Power Pocket provides 12V of portable power for hand held radios or any consumer electronic product.
Equipped with a cigarette lighter socket, use your cigarette lighter adapter to power all kinds of devices. Thermal switch protects against short circuits and over charging, recharges in 6-8 hours and weighs only 30ozs.
Included accessories:
Soft case
Shoulder strap/belt strap and belt loop on the soft case
Wall charger |
|
|
| | CS-201 | Frequency Range (up to): 600MHz
Power Rating:
2.5 kW PEP
1 kW CW
VSWR: below 0.12
Insertion Loss: less than 0.2 dB
Isolation: 60 dB 600 MHz
Connector: SO 239
Output Port: 2 |
| | | |
|
| | CS-201GII | Frequency Range (up to): 2 GHz
Power Rating:
1.5 kW CW (up to 30 MHz)
250 W CW (up to 1 GHz)
150 W CW (up to 2 GHz)
VSWR: below 1:1.3 at 1.3 GHz
Insertion Loss: less than 1.2 dB at 1.2 GHz
Isolation: 50 dB 1 GHz
Connector: Gold Plated N-Type
Output Port: 2 |
|
|
AVAILABLE FROM
&
MAYBE YOU WOULD LIKE TO BECOME A "WADSWORTH SALES" DEALER? MANY OF OUR DEALERS WORK FULL TIME JOBS AND DO THE RADIO BUSINESS AS A "SIDE BUSINESS". WE HAVE MANY
ESDA/RACES/ARES ORGANIZATIONS, GMRS AND COMMERCIAL 2-WAY DEALERS AS WELL.
IF YOU THINK YOU MIGHT LIKE TO INVESTIGATE THIS VENTURE JUST E-MAIL OR GIVE US A CALL!
BEING A MANUFACTURER'S REPRESENTATIVE WE PROCESS NO ORDERS DIRECTLY
BUT INSTEAD SET UP DEALERS AND DIRECT END USERS TO OUR DEALERS.
BRYAN WADSWORTH
CELL PHONE (815) 790-4494
SKYPE PHONE = bryan.wadsworth
FAX (815) 363-6056